WARNING!: It is vital for the safety of persons to follow all instructions. Failure to comply with the installation instructions and the safety warnings may result in serious personal injury and/or property and remote control opener damage. Please save these instructions for future reference.
Technical Specifications
| Model | SYNCRO ATS-3AMB | SYNCRO ATS-3AM | TEMPO ATS-2AMB |
| Input Voltage | 120Vac / 60Hz | 120Vac / 60Hz | 120Vac / 60Hz |
| Current (Max) | 2.0A | 2.0A | 2.0A |
| Transformer secondary output Voltage | 24Vac | 24Vac | 24Vac |
| Motor type | 24Vdc geared motor with permanent magnet | 24Vdc geared motor with permanent magnet | 24Vdc geared motor with permanent magnet |
| Shuttle travel distance in the C-Rail | 9.19ft (2.8m) approximately (standard) | 9.19ft (2.8m) approximately (standard) | 9.19ft (2.8m) approximately (standard) |
| Maximum shuttle travel distance in the C-Rail | 16.4ft (5m) (with extended C-Rail) | 16.4ft (5m) (with extended C-Rail) | 16.4ft (5m) (with extended C-Rail) |
| Peak Short Term Pulling Force | 1000N | 1000N | 1000N |
| Maximum door hanging weight | 520lbs (236kg) | 520lbs (236kg) | 440lbs (200kg) |
| Receiver type | UHF Multifrequency FM- Receiver | UHF Multifrequency FM- Receiver | UHF Multifrequency FM- Receiver |
| Receiver code storage capacity | 14 X 4 button transmitter codes | 14 X 4 button transmitter codes | 14 X 4 button transmitter codes |
| Transmitter frequency | 433.47MHz; 433.92MHz; 434.37MHz | 433.47MHz; 433.92MHz; 434.37MHz | 433.47MHz; 433.92MHz; 434.37MHz |
| Coding type | TrioCode128™ | TrioCode128™ | TrioCode128™ |
| Number of code combinations | Over 4.29 billion random codes | Over 4.29 billion random codes | Over 4.29 billion random codes |
| Code generation | Nonlinear encryption algorithm | Nonlinear encryption algorithm | Nonlinear encryption algorithm |
| Remote control battery | CR2032 | 3 Volts | CR2032 |
| Courtesy light | 2 LED Modules | 2 LED Modules | 2 LED Modules |
| Control board fuse | 10A (slow blow) | 10A (slow blow) | 10A (slow blow) |
| Battery backup | 2 x 12PCA 1.3 – 12V1.3 AH Batteries | Battery compatible, (requires optional Battery Backup kit) | 2 x 12PCA 1.3 – 12V1.3 AH Batteries |
| Network connectivity | Network ready, Smart hub already installed | Network ready, Smart hub already installed | Network compatible, (requires optional Smart Phone Control Kit) |
Operating Controls:
| Button | Function |
| 1. DOWN ARROW (Blue) | Closes the door |
| 2. DOWN ARROW LED (Blue) | Illuminates when the door is closed and flashes when the door is obstructed on close or stopped. |
| 3. STOP (Red) | Stops the door |
| 4. UP ARROW (Green) | Opens the door |
| 5. UP ARROW LED (Green) | Illuminates when the door is open and flashes when the door is open with the auto-close timer running, obstructed on opening or stopped. |
| 6. MODE (Yellow) | Enables Load Diagnostics Mode |
| 7. MODE STATUS LED (Yellow) | Illuminates when in Diagnostics Mode |
| 8. BATTERY STATUS LED (Yellow) | Illuminates when battery is charged and flashes when battery is charging, in use or battery failed. Battery function not available with ATS-2 model. |
| 9. REMOTE CONTROL STATUS LED (Red) | Flashes on remote lockout and flickers on remote control activity |
| 10. ADJUSTMENT LED (Yellow) | Flashes a certain number of times depending on the parameter being changed. |
| 11. NETWORK LED ( ATS-3AMB Only) | Is a dual colour LED. Illuminates purple when hot spot active, blue when connected to cloud and red when in production mode. Flashes different colour depending on the activity. |
Kit Contents:
- 1 x ATS drive unit
- 1 x Wall mount transmitter kit
- 2 x Transmitters and batteries
- 1 x Bent arm door attachment
- 1 x Straight arm door attachment
- 1 x Wall bracket TS01
- 1 x Door bracket Locator
- 1 x Door bracket
- 3 x Pin Snap SSP 8 ZNU 31080
- 2 x Hex Head screw M8x25
- 11. 1 x Pin 0890
- 2 x Clevis Pin 0829
- 2 x Hex Serration flange nut M8
- 4 x Hex flange screw taptite ‘S’ M4 x 10
- 1 x Wired Safety Beam kit
- 2 x Track Bracket
- 1 x Pre-Assembled C-Rail
Installation Instructions:
- READ AND FOLLOW ALL INSTALLATION INSTRUCTIONS.
- INSTALL ONLY ON A PROPERLY OPERATING AND BALANCED GARAGE DOOR. AN IMPROPERLY BALANCED DOOR HAS THE POTENTIAL TO INFLICT SEVERE INJURY. HAV E A QUALIFIED SERVICE PERSON MAKE REPAIRS TO CABLES, SPRING ASSEMBLIES, AND OTHER HARDWARE BEFORE INSTALLING THE OPENER.
- REMOVE ALL PULL ROPES AND REMOVE, OR MAKE INOPERATIVE ALL LOCKS CONNECTED TO THE GARAGE DOOR BEFORE INSTALLING OPENER.
- WHERE POSSIBLE, INSTALL THE DOOR OPENER 7 FEET OR MORE ABOVE THE FLOOR. FOR PRODUCTS HAVING AN EMERGENCY RELEASE, MOUNT THE EMERGENCY RELEASE WITHIN REACH BUT AT LEAST 6 FEET ABOVE THE FLOOR AND AVOIDING CONTACT WITH VEHICLES TO AVOID ACCIDENTAL RELEASE.
- DO NOT CONNECT THE OPENER TO SOURCE OF POWER UNTIL INSTRUCTED TO DO SO.
- LOCATE THE CONTROL BUTTON: (A) WITHIN SIGHT OF DOOR. (B) AT A MINIMUM HEIGHT OF 5 FEET ABOVE FLOORS, LANDINGS, STEPS OR ANY OTHER ADJACENT WALKING SURFACE SO SMALL CHILDREN ARE NOT ABLE TO REACH IT. (C) AWAY FROM ALL MOVING PARTS OF THE DOOR.
- INSTALL THE ENTRAPMENT WARNING LABEL NEXT TO THE CONTROL BUTTON IN A PROMINENT LOCATION. INSTALL THE EMERGENCY RELEASE MARKING. ATTACH THE MARKING ON OR NEXT TO THE EMERGENCY RELEASE.
- AFTER INSTALLING THE OPENER, THE DOOR MUST REVERSE WITHIN 2 SECONDS WHEN IT CONTACTS A 1 1/2
- -INCH HIGH OBJECT (OR A 2 BY 4 BOARD LAID FLAT) ON THE FLOOR.
- FOR PRODUCTS HAVING A MANUAL RELEASE, INSTRUCT THE END USER ON THE OPERATION OF THE MANUAL RELEASE.
Rail Assembly:
Installing the C-Rail
- Remove the Opener from the box.
- Locate and insert the shaft of drive unit into the C-Rail’s sprocket.
- Fix the two track brackets with four (4) M4 x 8 screws supplied in accessory pack.
- Place drive unit back in packing box for protection.
Mounting Operator for a Track Type Door:
Determine Bracket Position
- Determine the centre of the door and mark this point with a line on the wall above.
- Raise the door and find the highest point of travel of the first (top) door panel.
- Using step ladder and a level, transfer this height to the wall above the door and mark a line 2.36”(60mm) above it, across the centre line.
Mounting the Wall Bracket
- Draw two lines extending 0.846” (21.5mm) from each side of the centre point
- Centre the wall bracket over the intersection of these two lines. Mark centers for at least two holes and ensure it is into a solid mounting point.
- Drill holes in the wall with an appropriate bit.
- Secure to the wall using:
- IF CONCRETE OR BRICK: 8mm (5/6”) loxins/dynabolts.
- IF TIMBER:
- wood screw #20 or similar (minimum 1.97” 50mm long
User Operating Controls
| Button | Function |
| 1. DOWN ARROW (Blue) | Closes the door |
| 2. DOWN ARROW LED (Blue) | Illuminates when the door is closed and flashes when the door is obstructed on close or stopped. |
| 3. STOP (Red) | Stops the door |
| 4. UP ARROW (Green) | Opens the door |
| 5. UP ARROW LED (Green) | Illuminates when the door is open and flashes when the door is open with the auto-close timer running, obstructed on opening or stopped. |
| 6. MODE (Yellow) | Enables Load Diagnostics Mode |
| 7. MODE STATUS LED (Yellow) | Illuminates when in Diagnostics Mode |
| 8. BATTERY STATUS LED (Yellow) | Illuminates when battery is charged and flashes when battery is charging, in use or battery failed. Battery function not available with ATS-2 model. |
| 9. REMOTE CONTROL STATUS LED (Red) | Flashes on remote lockout and flickers on remote control activity |
| 10. ADJUSTMENT LED (Yellow) | Flashes a certain number of times depending on the parameter being changed. |
| 11. NETWORK LED (ATS-3AMB Only) | Is a dual colour LED. Illuminates purple when hot spot active, blue when connected to cloud and red when in production mode. Flashes different colour depending on the activity. |
Note: To download the user manual kindly click on the following link download button: