Checking the supplied items:
Check the following items are present.
- Digital Paper device (1)
- Stylus (1)
- Replacement tips
- Felt (gray) (1)
- POM (black) (2)
- Tip puller (1)
- USB cable (1)
- Quick Start Guide (this document) (1)
- Warranty (1)
Initial setup:
Set up the Digital Paper device (hereafter referred to as “the device”) and your computer according to the instructions displayed.
- Turn on the device.
- Set a stylus according to the instructions on the screen.
- Turn on the computer and connect to the Internet.
- Download Digital Paper App from the following site and install on the computer.
- Start Digital Paper App and connect the supplied USB cable to the USB connector of the device and the USB connector of the computer.
- Set the computer according to the instructions displayed by Digital Paper App.
- Documents can be transferred only between the device and the computer. Update the app software if a software update is advised
Charging the device and stylus:
- Turn on the computer.
- Connect the supplied USB cable to the USB connector of the device or stylus and the USB connector of the computer.
How to use the system and the support site:
For more detailed information on using the Digital Paper System, see support YGD UiVG
If you cannot recover the device:
Consult the Support Center and provide the following information.
- Model name (specified on the back panel)
- Serial number (specified on the back panel)
- Purchase date
Replacing the stylus tip:
The stylus tip may wear out through use. It is recommended to replace the tip when it becomes shorter than 1.5 mm (1/16 in). Replacement tips and a tip puller are supplied with the device.
- Pinch the tip with the supplied tip puller, then pull it out straight.
- Check the orientation of the replacement tip, pinch it with the tip puller, then push it straight into the stylus.
- Push the tip firmly with your finger.
Precautions:
Safety:
Handling the device:
- If the device causes interference to radio or television reception, turn the device off and move it away from the radio or television.
- Refrain from using the device in an aircraft according to the inflight announcements during taking off or landing.
- When you put the device into a bag, make sure no objects with sharp or hard edges come into direct contact with the device.
- Do not drop, or put any heavy object on top of the device or apply a strong shock to the device. It may cause a malfunction or damage.
- Never subject the device to extremes of light, temperature, moisture or vibration.
- If part of the device that generates heat contacts your skin for a prolonged period, you may suffer burn symptoms, such as redness, swelling, even if the temperature is moderate. Avoid prolonged contact, especially if you have sensitive skin.
- Do not leave the device on an unstable surface.
- Do not poke people with the supplied stylus.
- Do not treat or use the supplied stylus roughly, such as bending it, or scratching the touchscreen with it.
Avoiding water and moisture:
- Note that condensation may form temporarily in cases such as when the player is moved quickly from a low-temperature environment to a high temperature environment or used in a room that has a heater just turned on. Condensation creates a phenomenon where moisture in the air adheres to surfaces such as metal panels, etc., and then changes to liquid. If condensation forms in the device, leave it turned off until the condensation disappears. If you use the device with condensation present, a malfunction may result.
- The device is not waterproof. Remember to follow the precautions below.
- Be careful not to drop the device into a sink or other container filled with water.
- Do not use the device in humid locations or bad weather, such as in the rain or snow.
- Do not get the device wet.
Charging the device
- Heat may build up in the device while charging, or if it is used for an extended period of time.
- Use the supplied USB cable only. Do not use any other USB cable.
- Never wrap the device in anything when it is being charged. Heat build-up in the device may cause malfunction or damage.
Cleaning the device
- Clean the device with a soft cloth, such as a cleaning cloth for eyeglasses. Make sure that there is no dust or dirt on the soft cloth, as the device may be damaged.
- Do not use any type of abrasive pad, scouring powder or solvent, such as alcohol or benzene, as it may mar the finish of the case.
- Wipe the stylus with a dry cloth when it gets dirty. Tapping or dragging on the touchscreen using a dirty stylus may damage the surface.
- Be sure to keep the device away from water or spills.
Important information:
Safety:
- Do not expose the battery to fire or heat. Do not disassemble the battery.
- It may cause electric shock. Do not remove the battery yourself. For battery replacement, internal checking or repair, consult the Support Center.
- Do not charge the device near fire, heat, or leave it in hot sunlight.
- Do not leave coins, keys, jewelry, etc., near the USB connector or USB cable.
- Do not use the device while moving.
- Do not operate the device or watch the display while driving a vehicle, riding a motor cycle, walking, etc.
Specifications:
Model:
13.3″ : EL313ZZ
10.3″ : EL310ZZ
Basic information:
| Display | Electrophoretic display 16-level gray scale |
| Touchscreen | Projected capacitive touchscreen capable of pen input |
| Internal memory capacity (for data storage)/User available capacity | 32 GB/Approx. 20 GB |
| Interface | USB connector |
Power source
| Battery | Built-in rechargeable battery |
| 75$ | 58/3#, 98/2#, 128/2# |
| Operating/Charging temperature | 5 °C to 35 °C (41 °F to 95 °F) |
Dimensions/Mass
| Dimensions (w/h/d) | 13.3″ : 222.8 x 301.1 x 5.7mm 10.3″ : 173.2 x 242.5 x 5.9mm |
| Mass (including battery) | 13.3″ : 358g 10.3″ : 255g |
Note: To download the complete user manual, please download the following file: