INTRODUCTION
Potensic Dreamer 1 is equipped with intelligent flight control system, which can realize the functions of way-point flight, intelligent follow, and auto return home. With a 1/3 inch Sony CMOS image sensor and a camera anti-shake system, the camera can stably shoot up to 30 frames per second of 2.7K high-definition video and 4.0 million pixels of photos.
Maintainence:
- Use a clean soft cloth to clean this product frequently.
- Avoid heating or prolonged exposure to the sun.
- Don’t put the product in water. It will damage electronic parts.
- Please check the plug and other accessories a regular intervals. If there is any damage, please stop using it immediately until it is repaired completely.
Blades:
Press down and rotate according to the marked direction of blade locking until it cannot be turned; unload the blade, reverse the above steps.
When installing, please pay attention to the right rotating direction of the blades, which are printed with “CW” and “CCW”. So, you need to install them according to “CW” and “CCW” marks.
BATTERY:
BATTERY CHARGING
When the drone’s power is too low, please fly the drone back and charge the battery in time. Connect the adapter to charge the battery. When charging, the indicator flashes. When full charged, the battery indicator lights will be off. The full charging time is about 2 hours.
BATTERY INSTALLATION AND TAKING OUT
As shown in Pic 1, insert the battery in the right direction into the drone. As shown in Pic 2, pinch the buttons on the left and right sides of the battery and pull out the battery.
Camera:
- Install the shock absorber ball on the shock absorber board and install the anti-tripping device.
- Insert the power cable and steering wire of the camera into the connector of the aircraft adapter board, respectively.
- Close the connecting wire cover.
MICRO SD CARD:
Inset the Micro SD card into the camera SD card slot. It is recommended to use the brand product such as SanDisk, Kingston or Samsung, and needs Micro SD cards with at least 4GB and max up to 256GB. All the pictures and videos will be only saved in Micro SD card and not in App or your phone. The Micro SD card is not included in the package.
KNOW YOUR REMOTE CONTROL
Dreamer1 uses a 2.4G remote controller with complete function keys. It can complete various operations and settings of aircraft and the camera within a maximum communication distance of 500 meters and display high-definition pictures on mobile devices in real time through App “Potensic Pro”. The remote controller is equipped with rechargeable lithium batteries, which can work continuously for up to 4 hours.
CHARGING INSTRUCTIONS
Connect the Micro USB interface of the remote controller to charge the most commonly used 5V/2A charger. Full charging takes about 2 hours.
DRONE FLIGHT MODE
Dreamer 1 uses a new generation of Potensic flight control, which supports the following flight modes
GPS mode: Accurate hover, pointing flight and other intelligent flight modes are realized under the GPS mode. Under the GPS mode, when the GPS signal is strong, it can be positioned accurately. when the GPS signal is weak, the aircraft can not be positioned accurately, and it only provides attitude stabilization, and does not support intelligent flight function.
Attitude mode: With the GPS is off, only attitude stabilization is provided. At this time, the maneuver rocker is used to control the flight of the aircraft. This mode is used cautiously by novices.
SPECIFICATION:
DRONE
Flying weight: 740g
Maximum ascending speed: 5 m/s (sport mode); 3 m/s (normal mode) Maximum descent speed: 3 m/s (sport mode); 3 m/s (normal mode) Maximum horizontal flight speed: 8 m/s (sport mode); 5 m/s (normal mode) Flight time: about 30 minutes
Working ambient temperature: 0°- 40° C Satellite positioning systems: GPS + GLONASS
Working frequency: 2.402 – 2.483GHz and 5.725 – 5.850GHz Transmitting power: 2.4GHz:<18 dBm
5.8GHz: <24 dBm
Hovering accuracy (vertical): +0.1 m (when GPS positioning works normally) Hovering accuracy (Level): +0.3 m (when GPS positioning works normally)
CAMERA
Image sensor: 1/3 inch Sony CMOS; effective pixel 4.0 million Lens: FOV 78 degrees
Maximum resolution: 2688 x 1512 Photo shooting mode: single shot Controllable range of rotation: +0° -90° Video resolution: 2.7K: 2688 x 1512 30p
Maximum video storage bit stream: 20 Mbps Supporting file systems: FAT32
Picture format: JPEG
Video format: MP4 (AVC/H.264)
Support memory card type: Micro SD card; at least 4GB and maximum support 256GB, transmission speed of class 10 or above Micro SD card.
Working environment temperature from 0° to 40° C
REMOTE CONTROLLER
Working frequency: 2.402 – 2.483GHz
Maximum effective distance of signal: 500m (under environment with no interference and no
occlusion) Working environment temperature: 0° ~ 40°C. Battery: 1200mAh lithium battery, 1S
Equivalent Omnidirectional Radiation Power (EIRP) 2.4GHz: <16 dBm Operating voltage / current: 3.7 V / 0.15A
SMART BATTERY
Capacity: 3000mAh Voltage: 15.2V Battery type: Li-Po 4S Energy: 45.6Wh
Battery overall weight: 255g
Working environment temperature: -10°~40°C Maximum charging power: 26.25W
CHARGER
Rated input: 100-240V ~ 50 / 60Hz, 1.5A Rated output: 17.5V, 1.5A
Rated power: 26.25 W