Package Contents
Powering on and Pairing
1. Take out earphones from the charging case.
2. Select ‘ENACFIRE E90’ from Bluetooth list.
Pairing Without Charging Case
1. Power On: Touch the earphones for 2 seconds. Release when you hear the 5 prompt sound ‘Power on with blue light on.
2. Pairing: Earphones will pair automatically with right earphone blue and white light flash alternately.
3. Select ‘ENACFIRE E90’ from the device’s Bluetooth list.
Note:
The right earphone is the master earphone.
Product Images
Incoming Call
Answer call/end call Tap the Left/ Right earphone once.
Reject Call
Touch the Left/ Right earphone for 2 seconds.
Music
Pause/ Play
Tap the Left/ Right earphone once to pause /play music inthe music mode
(Some phones may require to start a media player first)
Voice Assistant
Tap the Left /Right earphone 3 times, your device’s Voice Assistant will be activated with the ‘Beep’ prompt sound
Next Song
Double-tap the Right earphone.
Previous Song
Double-tap the Left earphone.
Adjust Volume
Touch and hold the Left earphone to decrease volume Touch and hold the Right earphone to increase volume.
Note:
Above functions are not supported when the earphone is used in single. Prompt sound ‘Beep’ will be produced when the volume reach minimum or maximum level.
Powering Off
Mode 1: With Charging Case
Put the earphones back to the charging case, they will power off automatically.
Note: Only put the Left earphone into the charging case, the Right earphone will stay connected.
Only put the Right earphone into the charging case, the Left earphone will be disconnected and start pairing.
Mode 2: Without Charging Case
1. Turn off Bluetooth to disconnect the earphones
2. Touch either one earphone for 8 seconds to power off both earphones
Single Mode
Note:
There will be 2 ‘ENACFIRE E90’ Bluetooth names show on your Bluetooth list if you have connected the Left and Right earphone singly before. Please try to select the another ‘ENACFIRE E90’ if you are unable to connect the earphone singly.
(You can edit the device’s name in Bluetooth list under Android system)
Charging
Earphones Charging Status
Open and close the charging case cap, wait for 3 seconds The leftmost LED light on: Left earphone is charging
The rightmost LED light on: Right earphone is charging When the earphone is fully charged, LED light will turn off
Note: Ittakes about 1.5 hours to fully charge the earphones
Charging Case Charging Status
Open and close the charging case cap
Lights on charging case stand for the remaining battery capacity
Note: It takes about 1.5-2 hours to fully charge the charging case
Download User Manual
Note
Please follow below steps when both earphones fail to pair with each other or occur connection related issues
1. Turn off Bluetooth to disconnect the earphones
2. Touch either one earphone for 8 seconds to power off both
earphones 3. Touch and with White 4, Touch and with White
hold the power button of Left earphone for 8 seconds lights flash 3 times
hold the power button of Right earphone for 8 seconds lights flash 3 times
5. Put the earphones back to the charging case
6. Delete al ‘”ENACFIRE E90’ related Bluetooth names from your
phone
7. Turn on Bluetooth and reconnect the earphones
Note: Do not touch and hold the power button of both earphones at the same time, please do iton sequential order
Safety
Using earphones at high to moderate volumes for extended periods of time will result in permanent hearing damage. It is advised that you keep volume levels moderate to low at al times for your safety. Do not use while driving, cycling, operating machinery or performing other activities that require hearing surrounding sounds.
Do not use earphones in thunderstorm weather, the earphones may not work properly in the bad weather condition, and may increase the risk of being hit by lightning.
Earphones may not work properly under high temperature or high humidity conditions.
Do not use any corrosive cleaner/oil to clean the earphones. Ifthe earphones come in contact with liquids, quickly wipe away. If submersed in the water, do not turn the earphones on until it is completely dried.
Tips: Man-made damage and lost are not covered under warranty. Keep the earphones and the packaging out of reach of children.
Questions and Answers
Q: Why the music cuts in and out sometimes?
A: Please make sure there is no obstacle between the earphones and your device. Please make sure there isno Microwave oven /Wifi transmitter around you, which are more likely to produce electromagnetic interference and result in signal interruption.
Note: Please keep your phone and the master earphone (R) as close as possible to ensure a more stable Bluetooth connection.
Q: What should |do if the earphones stop charging?
A: We recommend you to charge the earphones by using our cable. If our cable do not work, please try to use another charging cable or power source to charge the earphones.
Contact Information
If you have any issue with the product, please contact us via support@enacfireglobal.com (US /CA) moongu@enacfireglobal.com (UK)
We will reply to you within 24 hours and 100% solve your issue.