Charging the rechargeable battery pack for the RC vehicle:
- Locate a USB certified port from any of the devices shows below. The LED indicator inside the USB Cable will turn green.
- Connect the 6.4V Li-ion rechargeable battery pack and the USB Cable connectors, then the LED indicator will turn off to show it is charging.
- Once the LED indicator turns green again, the battery is fully charged. It takes around 1.5 nours to fully charge the battery. However, even the LED does not turn green, do not charge the battery more than 2 hours.
- When charging is completed, detach the connectors from battery pack and USB certified port.
Note: If the LED twinkle slowly, then the USB Cable is not able to work properly. Try to connect the USB Cable to another USB port, if the problem persist, immediately disconnect the battery and the USB Gable and seek replacement.
Battery installation for the controller: (Refer to Diagram 2)
- Switch the power OFF.
- Use screwdriver to loosen the screw on the battery cover and to open the battery cover. (Screwdriver is not included)
- Install 2 new 1.5V “AA” LR6/R6 battery with correct polarity (+/-) as shown inside the battery compartment.
- Install the battery cover and then tighten the screw on the battery cover.
Battery installation for the vehicle: (Refer to Diagram 3 & 4)
- Switch the power OFF.
- Rotate the battery cover latch aside and open the battery cover.
- Install 6.4V Li-ion rechargeable battery into the battery compartment. Connect the rechargeable battery pack to the socket in tne battery compartment.
- Install tne battery cover and turn the latch to lock it in position.
- The “Power LED” on the vehicle will not flash nor stay on if the rechargeable battery has run out power.
How to play: (Refer to Diagram 4, 5 & 6)
Set the “Power Switch ‘ on the controller and vehicle to ON position, the ”Power LED” on both the controller and vehicle will flash less than 3 seconds then stay on, meaning the automatic frequency matching between the controller and the vehicle is completed. If the “Power LED” of the controller or the “Power LED” of the vehicle flash Power LED more than 3 seconds, switch off both the vehicle and controller, then turn them on again.
Pull the trigger in the transmitter half way to drive the vehicle forward. Pull the trigger full way to obtain extra speed. Push the trigger in the transmitter to drive the vehicle backward.
Turn the steering knob in the transmitter to steer the vehicle to right or left.
If the vehicle went too far and out of control, switch off both the vehicle and controller, then turn them on again.
If the vehicle does not run in a straight line, adjust the wheel alignment under the chassis.
The headlights will be turned on when the vehicle is moving forward.
Turn the switch of the controller and vehicle to OFF position when not in play.
Performance Tips:
- Do not drive the vehicle on grass. sand or go through water.
- Do not drive the vehicle in windy or rainy weather.
- Do not drive the vehicle into any hard object.
- Keep fingers, hair and loose clothing away from the vehicle.
- It’s not allow children to ride on the vehicle.
- The operating range can be affected by a variety of factors:
- Weak controller or vehicle batteries.
- Interference from other items that emit radio frequency signals such as another R/C item on the same frequency, CB radios, cordless phones, high voltage transmitter, etc.
7. Outdoor usage is recommended in order to get optimal control range.
8. Remove the package, take out all accessories and assemble the product.
Cautions:
- The 6.4V Li-ion battery pack must be charges before use. Use only the battery pack and USB Cable that came with this vehicle.
- Do not overcharge the Battery Pack. Do not charge for more than 2 hours except for the initial two charges.
- Do not charge the Battery Pack if it shows leakage, corrosion, or has loose or exposed wires or other damage.
- Do not cover the Battery Pack with any sort of material while charging.
- Do not touch the Battery Pack when it is hot. Wait until the Battery Pack cools before installing it in the Vehicle and before recharging.
- Do not dispose of the Battery in fire.
- Do not dismantle the Battery or USB Cable, and do not cut the Battery or USB Cable.
- The Battery Pack will be warm after charging, and hot after use in a Vehicle.
- The supply terminals are not to be short-circuited.
- Rechargeable Batteries are to be removed from the toy before being charged.
Contents:
• RC Vehicle x 1
- Controller x 1
• USB Cable x 1 (Input: DC 5V 2A Output: DC 6.4V 1A)
• 6.4V Li-ion Rechargeable Battery Pack (For Vehicle Use) x 1
- 1.5V “AA” LR6/R6 non-rechargeable Battery (For Controller Use) x 2
• Owner’s Instruction Manual x 1