EZ-Bell User Manual

D-3 TECHNOLOGY LIMITED EZ-Bell

Introduction

Next generation video doorbell camera – EZ-Bell is your multifunctional doorkeeper, enabling you to receive doorbell alarm and home security event alarm, to make calls with visitors, to view real time streaming or motion trigger video and playback video.

Included Materials

  • Doorbell Camera*1
  • Wall mounting bracket*1
  • Angle correction plate*1
  • Wall screw*2
  • Doorbell fixing screw*3
  • Expansive rubber sleeve*2

Product Appearance

Product Features

  • Live view streaming via Mobile APP or Security Panel.
  • Two-way Audio through Mobile APP or Security Panel.
  • Security RF included. Connecting the complete ecosystem: Panel, Sensor, Doorbell.
  • Expansive FOV 202(H)*119(V).
  • Full HD 1920 x 1080 Video resolution.
  • 2T2R Dual band 2.4GHZ/5GHZ WIFI for improved WIFI range.
  • On-device AI. Instant analysis of each event and accurate reduction of false triggers.
  • Real time communication to anyone who approaches your door via 2-way Audio.
  • Pre-record supported. Capture all actions in video clips to be stored at Amazon server.
  • As a sensor to Panel, doorbell camera can send outdoor motion events to Panel.
  • Compatible with the existing doorbell transformers (10-30VAC,10VA)
  • Compatible with Mechanical and Digital Chimes.

Product Images

Product Specifications

Model Name: EZ-Bell V1 (XDC01)Video compression format H.264+ AAC/PCM
For Video Clip and Video streaming
Memory: 2GBit Embedded DDR3Network protocol P2P Video streaming/ Camera configuration HTTPS and OTA support
Image sensor: 1/2.7″ FHD (1080P) sensorNight Vision B&W Night Vision/850nm @16ft
Streaming resolution: HD(720P)/FHD(1080P)LED RGB color status LED
Video framerate Variable framerate 10-15fpsChime Security Panel (XP02) as Doorbell Chime AC Mechanical Chime
AC Digital Chime (Works with DDA board)
OS: Dual OS (RTOS + Linux 4.9)Storage: Local Storage: N/A (Reserved MicroSD Socket) Cloud Storage: Amazon KVS Video storage
Field of View: 202(H)*119(V)Power 10-30VAC, 10 VA, OR 12 VDC 0.5A Battery: Built-in 450mAh battery
WIFI/ SubG RF radio WIFI: IEEE 802.11 a/b/g/n/ac 2T2R 2.4/5GHz dual band SubG RF: 433MHzOperation Temperature Product working temperature: -10°C ~ 45°C
Motion Detect Motion sensor/130° @ 8FT
AI Human detection algorithm to reduce false trigger Support pre-recording before Motion trigger
Waterproof IPX4
Weight 94g
110g (with mounting plate)
Video /Audio Streaming Full-duplex two way callCertification FCC/IC

Requirements

Power

10-30VAC, 10VA or 12VDC, 0.5 to 1.0A wired to an in home mechanical or digital doorbell chime. Note: A Digital Doorbell Adapter must be installed if a digital doorbell chime is present. WARNING: An in-line resistor (10 Ohm, 10 Watt) is required when installing the doorbell camera without a wired, in-home doorbell chime. This is typically done when testing the doorbell or performing a demonstration. Failure to install a resistor when a chime is not present may result in damage to the doorbell camera.

Chime

  • Security Panel (XP02) as Chime – XP02 Panel can be a chime of the EZ-Bell doorbell.
  • Mechanical Chime – If the chime has metal bars and a striker pin, it is mechanical and will work without additional hardware.
  • Digital Chime – If the chime has a speaker that plays a tone when pressed, it is digital and will require the installation of the Digital Doorbell Adapter and the enabling of the digital doorbell setting in the app to function properly.
  • Tube Chime – If the chime has a series of tubular bells, it is a tube chime and is incompatible with the doorbell camera.
  • Intercom System – If the doorbell button fixture includes a speaker, it is an intercom system and is incompatible with the doorbell camera.
  • No Chime – If there is no chime in the system, the customer will only receive alerts on their phone and a resistor (10 Ohm 10 Watt) must be used in-line with the doorbell camera.

WIFI

Wi-Fi Internet upload speed of at least 1.5 Mbps is required at the location where the doorbell camera is installed.
Note: In Canada when using 5 GHz on band 1, the device is intended for indoor use only.

Hardware Installation

Setting Up/Pairing APP

Camera Pairing and Provision

  • Download Redbee application
  • Login to Redbee application
  • Click add camera
  • Wait while LED is orange
  • Allow Location
  • Click blue arrow
  • Click on WLAN in phone settings
  • Scan for network XDC01*****
  • Choose doorbell
  • Open Redbee application
  • Scan for WIFI
  • Choose WIF network you would like to use fo the doorbell
  • Enter WIFI password
  • Wait while the doorbell connects to the WIFI network
  • Set doorbell name
  • Your Redmee doorbell is now ready to use!

Live View Streaming and 2-Way Talk

Video Clip Online Playback

Redmee LED Light Meanings

EZ-Bell User Manual Download